metal particles in gear oil from final drives in takeuchi tl140

i changed the oil in my final drives on a 06 takeuchi tl140 with 700 hours. this was the second time i changed oil. old oil came out frothy...with air bubbles. and the old oil had lot of metal "glitter" in it. i installed new oil and ran for a bit and drained it out, and replaced with new oil. ran another few hours and replaced oil again. still see "glitter" in the drained oil.
should i be concerned? running 75w-90 oil. would thicker oil provide more protection?

Show us your hobby's

This is mine, The wife and friends say i'm crazy, But hell i have some fun, Off to compete at our most popular and Biggest Burnout comp in Oz in January 2011 (just remember this car is right hand drive) Thats me steering

http://www.youtube.com/watch?v=0T3-rsJsXYk&hd=1

What's your hoe doing?

Hi All, I saw a thread or two in other areas that are a showcase of the projects you have but I hadn't seen one in this section... I'm curious to know both what projects you've done, and what get's your BHL's use most.

I'll post a few pictures below and I'll have to update some as well. My biggest use is knocking over dead trees and dragging them back to a pile or two and digging holes in the pond to build the big dirt pile seen in one of the pictures or creek to fill in holes from removed...

What's your hoe doing?

Zx30u-2 seal kit for cylinder arm

Can someone please help me locate a seal kit for my zx30u-2. My local dealer cant help me because the part# doesnt come up in his computer. 4634032. Any help is appreciated. Thanks

Possible H.E.F. Merchandise?

Since the calendar post, went to far! To be serious, I would like to see an online store. How about you others?

Kubota excavator 4.5-5 tonne.

Looking for information on early Kubota excavators,20-30 years old ? Up to 5 tonne range,is their a thread I have missed finding or does any members have info/pics would be good,thanks Garrie.:notworthy

White-GMC 94’ STC 330 N14

Yep I went and got the truck, just never made it home with it “yet” asking was $6500 got it for $5250, 313k miles and I will update more specs later with pictures. Anywho about that “yet” part I’m sitting here in it about 300 miles from home off exit 200 in North Dakota after it decided after 175 miles to lose power. Started down to 55 mph and after all is said it crawled in at 5 mph, so I guess I get iron problems out on the road at midnight. Opened up water drain valve it spit some out...

White-GMC 94’ STC 330 N14

Caterpillar 12e clutch removal

Hi.
I have the engine out of my old Cat 12e grader. I am going to scrap it for parts. Part it out.
A guy with an old d6 wants the D333 engine.
I don't think he probably needs the bellhousing and clutch. Surely an old d6 dozer would use a different clutch and bellhousing?

I have removed the bolts around the clutch assembly. It seems the clutch wont budge loose from the flywheel?
Is there something I don't know? What do I have to do to get the clutch off so I can get the flywheel and...

Caterpillar 12e clutch removal

Komatsu D38E-1 Pops out of Reverse

The machine pops out of reverse but all the pressures are good. It doesn't matter which range it is in. Machine has a joystick control for direction, range and steer right or left. When in reverse it seems to me that the control has no detent left and easily pops out of gear. I checked the parts book which only shows a detent for the range selection. Basically turning the handle changes the ranges. There is nothing shown on the spools for direction. Looking at the diagram, it looks like only...

Komatsu D38E-1 Pops out of Reverse

Cat 3126 rear main install tool

I'm going to have to put a new rear main seal in a cat 3126 sometime in the near future. When I get tired of it puking oil on the ground.

A guy local to me has this on Craigslist- is this the only tool I need, or do I need another adapter? Seller states that it does 3126- but I don't know.

I have a seal install tool for a 3208, I guess I should look and see what part # it is.

https://springfield.craigslist.org/tls/d/mansfield-cat-rear-main-installer-kit/7096502668.html...

Cat 3126 rear main install tool

Cat 14M, good deal ?

Hello, we are looking to buy a used Cat 14M (CB9J00295) that have 13,000ish hours on it and I know that some series had more gremlins than other so advises are welcome!

If this serie is a good one, what should I look up to on these machines? Going to see it tomorrow

Thanks

CAT D8H Hydraulic GPM question

Folks

I have a D8H serial number 46A18325. I am mounting a Werk Brau tile plow on the machine. I need to know if the machine is open or closed center and what the GPM is of the hydraulics to get the correct control valve for GPS grade control on the drainage plow. Any suggestions on where to look up? I am pretty sure these machines were built open center for factory? How do you tell? Also the machine is a scraper tractor and I believe it was factory. Any info is much appreciated.

Thanks

Jon

Lists of projects

First up
Decide will try to establish gas to BILs chevy so load up to drop the GMc at the barn and attempt to motor the chevy to the shop.
Not today

Seems RF brake dragging severely
Have new caliper hoses so figured start there. Again Not today.
Local parts house will have calipers and pads in by morning, will assemble the new hoses to these then swap and install new pads.
RF both pistons freezing up extended, LF one piston has never moved out the other wants to hang and pads are all...

Lists of projects

Safety Thoughts From My Accident

This is coming from the bottom of my heart, Sep. 11 2019 I got out of the equipment to check some things and I walked up to the top of the tracks to check things out and I slipped off landing on my left leg in a weird position literally shattering my left femur into 20 plus pieces all by myself. I’m over a mile from the truck and I’d left my phone in the cab thinking I wasn’t going to be gone but for a few seconds to check everything. I woke up some time later next to the equipment from...

Safety Thoughts From My Accident

Cat 955 L

Hello to everyone, i am a new member to this forum, but i have found much help in the past in various posts.

I Just purchased a 955 L. I dont know the date of the machine, there is a small plate welded on the engine side of the "dashboard" that reads 8Y8710. Is that the serial number?

The loader has been sitting for two years due to cylinder head failure, combustion was leaking in the cooland circuit. The previous owner took the head out but never got it fixed.
I Had a look at the...

Cat 955 L

Hitachi 120-2 questions and anwsers

Hey everyone i bought a hitachi 120-2 last winter for 4,000 dollars which i thought was a smoking deal.
at first inspection the machine fired right up the idle up funtions worked. i moved the boom around and it seemed to bog the machine down. the guy i was with said it has got to be fuel filters."buy it" he said. so i did

one of the main reasons the people wanted to sell was because the machine had developed a new leak that was coming out of the middle of the undercarrage....

Hitachi 120-2 questions and anwsers

What’s this switchfor??

Can someone tell me what this switch does? The one with the lightning bolt. Machine is a 246b View attachment 225125

2001 Jcb 214 series 3

I’m confused folks. One guy says my machine is a 2001 Jcb 214-4T the other one says it’s a 2001 Jcb 214 series 3. Says series 3 on the machine but when buddy punches serial number in, it comes up as 214-4T. Anyway my serial number is low 90,000’s and I’m looking for parts breakdowns where I can find part numbers. Why is it such a big problem and secret as to why these machines are hard to locate info when they are out of Europe? I am having a real hard time locating the right service manual...

2001 Jcb 214 series 3

Hydraulic leak

CAT0299DLGTC00836

I have a big leak that appears to be coming from the right side track just below the hydraulic hoses on the bottom of the drive motor. Is this repairable?

Shuttle Transmission Case 680E

case 680 680e



I have a 680E that needs a transmission re-build.

It moves until it warms up, and then it stops. I believe the transmission fluid is bypassing the shuttle seals. long story short does anyone know where I can get a transmission re-build kit for it? or for that matter a re-built shuttle with the torque converter?

Thoughts on putting a magnet inside a final drive?

What do you guys think of placing a strong magnet on the inside of a planetary? To catch metal particles. Behind the cover. Or perhaps getting one of them very large magnets and just sticking it on the outside of the planetary cover?

2002 CAT 307C slow/weak hydraulics

Hello all!
So I am newish to owning/running equipment (was a crane mechanic for several years) and I recently purchased a 307C with 5200hrs on it. It was owned by a local privet water district and very well maintained. I have been putting it to use on my farm and the first few weeks it was operating very "quick" (hard to judge with no base line) and smooth. Recently I have noticed that operating multiple functions feels very slow and sometimes wont even actuate the function. Also traveling...

2002 CAT 307C slow/weak hydraulics

6-71 Detroit stuck at full throttle

Started our old Wabco 777 after sitting for 6 years or more. I thought it would take some doing but it fired right up and went to warp speed. The throttle did nothing and neither did the shutoff. So I cut the fuel line. I don't know Detroits but my guess is there's something stuck in the fuel control in the picture below. Any help is greatly appreciated. Sorry for the underlined words I don't know what I did. View attachment 224544 ...​

6-71 Detroit stuck at full throttle

Where is Case 580 Super L Rear Differential Part Number ?

I am going to change the fluid in the rear differential and planetary drives on my Case 580 Super L Backhoe. I found a reference that says the oil requirement is different depending on part number for the rear end on these machines - Axle Numbers 114367A2 and 114367A3 use MS1317 oil which is and 85W 140 with friction modifier. Axle numbers 114367A4 and later use MS1207 which is a HyTran Fluid.
I looked around on the rear differential but haven't found the part number yet...

Where is Case 580 Super L Rear Differential Part Number ?

location of hand pattern control changers on all machines. please list here

hey there.
i thought it might be a good idea to list the location of hand pattern control changers in a central location. i have been helping a large construction company part time because my business is slow and they have a gazillion pieces of equipment. getting off one machine and on another has become awkward due to the various hand patterns of each machine. i would really like to know where to find the hand pattern control changer on komatsu excavators sized pc200 and above???

cat...

location of hand pattern control changers on all machines. please list here

Catapillar 262D Code 2204-3 & 3700-3 Questions

I am new the forum and I just picked up a 2014 Cat 262D. The machine runs fine but I noticed the other day that there was an alert light that was staying on but not flashing. Just like that check engine light So I went into the settings finding the event log. It had two codes displayed. The first code was 2204-3 Machine, Auxiliary Lever #1 Position Sensor voltage above normal. The second code was 3700-3 Machine, Loader Bucket Inclinometer Sensor Voltage above normal. I checked online...

Catapillar 262D Code 2204-3 & 3700-3 Questions

wheel loader 330 L Transmetion

Hello Guys

i have my volvo 330L not controling te gear it works only on 2ND

Got bit by something...

Last Thursday I thought I got dust in my eye when a few guys came out to my MX track. My eye was kind of sore and not red or anything so I put some drops in hoping it would clean everything out. Also thought I could have a bit of a cold. A few days later and stiil sore and now a little red. I took a closer look and noticed I now have what appear to be 3 puffy bug bites in a row on the side of my forehead about 1/2 an inch from my eye. They look like giant mosquito bites but I suspect some...

Got bit by something...

Ford 555 coolant in oil

Ford 555 has a 3 cylinder diesel with a turbo that looks aftermarket.
Ive had it 6 months and it has been working great until yeasterday It wouldn’t turn over. The engine was hydro locked with fluid in the cylinders (mostly the rear one) when i removed the injectors it woud turn over and sprayed fluid out of the injector holes.

My first thought was i had water in the tank that was being injected into the cylinders but the volume of fluid In the cylinders seemed too great

My rad has had a...

Ford 555 coolant in oil

Where does old machinery go to die ?

Based in Melbourne, Australia.

Just wondering, where does machinery that's ready to be retired, go to. Cars go to car wreckers, but I've never heard of any such thing for machinery. Machines like excavators, bobcats, tracked dumpers, forklifts, industrial machines, etc.

I've got my own little shop with 3D cad, lathe, mill, cnc plasma, etc, so have some capabilities. I'm looking at making a purpose built machine, but rather than building from scratch would like to browse any such wrecking...

Where does old machinery go to die ?

Where to buy quality cyl seal kits online?

I have acquired a neglected Case 580E backhoe and am going thru and fixing leaks. For front loader cylinder, i purchased two cylinder seal kits:

$19 from eBay, all no-name seals, fit and finish seemed lower than the below kit.

$32 from foxkit, included at least one SKF marked seals. Quality of fit seems more precise than the above.

My questions:
- does the use of name-brand seals make a difference ?

-where do you shop for quality seal kits?

Thanks !

New to me EX120-2

Just picked up an Ex120-2 and excited to get to work on it, so it can work on our new homestead

It has leaks and a few quirks, but I have to say, spending time on here reading over the posts gave me the confidence to make the purchase.
One item though popped up that the owner didn’t mention.

The Boom up is painfully slow. You pull back on the stick, and you can hear a valve or something staving for oil. If you push down on the boom and slightly pick the machine up, then the boom up...

New to me EX120-2

773G air issues ??

Good morning all. I have a 773G and I ran into an issue over the weekend. I was cleaning up some brush when I heard a pop and what sounded like a punctured tire. I turned the machine off and checked all the tires, no flats. I started the machine and I hear the "air leak" again. It seems to be some where under the cab. I couldn't locate the problem. Any suggestions as to what I should look at ? Thanks in advance for the help.

Technical Service manual for JD 450E?

Hello to all,

I know I have received a lot of good info on this site and to all knowingly and unknowingly contributed... Thank you!

I recently bought a John Deere turbo 450E dozier from a customer. It has only just over 4K on it, undercarriage is approx. 70% and they just replaced the hydraulic pump, injector pump and injectors and the 6 way blade is still pretty nice and tight. It needs a transmission to engine clutch. - it slips after it is used for a bit. I checked the adjustment and...

Technical Service manual for JD 450E?

D6N Park Brake Solenoid

Can someone tell me where the left and right park brake solenoids are located?

Hydraulic Pump Cross Reference

Does anyone know of a source that could provide insight into which pump is in which excavator?

I am currently working with a JD 470GLC and there appear to be many pump options:

(not the serial number range I am working with)
SNs PIN: 1FF470GX_ _C047001-
--Pump PN 9184686EX

(I am working with this serial number range machine)
SNs PIN: 1FF470GX_ _E470001-
--Pump PN FYA00035147 or FYA00052949 or 4699645 or PG202165
then to confuse things more Alibaba references these numbers for the...

Hydraulic Pump Cross Reference

Dual Purpose Dump-Tractor

Has anyone made their dump truck into a dual purpose Dump-tractor? Something that the dump bed can easily be removed and a fifth wheel installed. I have some ideas floating around on how to do it, but looking to see what others have done too. Being a small operation and trying to stay cost effective this is one ave we are looking at doing.

Questions on buying a D6R

Trying to do my research on the D6R's before I purchase one. Don't know the serial number yet but going to look at it today or tomorrow. I'm not familiar with the Heui pump. Seen lots of bad post about it. It's an 04. What do I need to look for engine wise and anything else that's considerably different than the 6H's which I'm familiar with?

Austin Western 195X MotorGrader part or whole

I have a 59 model Austin Western motorgrader, it did run when parked about 12 years ago, I would like to sell it whole or part. Does anyone know where or how to sell it and/or part it out?

Walker's work doing's

Brand me frontier brush hog wrecked in 1hr repaired in 4 View attachment 157595 View attachment 157596

Buying & selling equipment

I am not sure if I am posting on the right place, I hope I do.
I wonder which web site lists/ads do you use when buying or selling equipment(ag, const...any)?
Which one is the best? What do you like about it, and what you don't?

Genie GS-2646 showing low voltage on charged battery

I just bought a Genie GS-2646. The previous owner said it was good to go and no issues. Looked fine put it through it's paces. Trucked it to my location and it had just enough power to roll down the ramp 10 feet. Now its saying low voltage.

One battery was bad so I swapped that out. I'm getting 25.8v right now which isn't full but I assume low is triggered something like 23v and 25.8 should be great.

The seller is no help saying it was great. They'll take it back which I'd prefer not to...

Genie GS-2646 showing low voltage on charged battery

1988 john deere 510c project

Hi, I recently took a chance on purchasing a jd510c that needed a main hydraulic pump. After checking around and getting quotes on buying a refurbished one I decided to try my hand at rebuilding the old one. I should add too that the backhoe sat around for at least two years and needed lots of tlc. I was successful in the rebuild and we managed to get it moving . The hydraulics were slow at first and we discovered multiple leaks which we fixed and now they are much faster. During...

1988 john deere 510c project

Schematic

Pls can someone help me with Dozer D6R AND D6H Schematic

850g case bulldozer controls get stiff after operating temperature is reached

I have a 850g case bulldozer. After running it for a couple hours my hi & lo levers and my control for the blade gets real stiff and starts to stick. I am lost. It's not building pressure in the tank and the oil is fresh. Any help would be greatly appreciated. Thank u for your time.

What's your hoe doing?

Hi All, I saw a thread or two in other areas that are a showcase of the projects you have but I hadn't seen one in this section... I'm curious to know both what projects you've done, and what get's your BHL's use most.

I'll post a few pictures below and I'll have to update some as well. My biggest use is knocking over dead trees and dragging them back to a pile or two and digging holes in the pond to build the big dirt pile seen in one of the pictures or creek to fill in holes from removed...

What's your hoe doing?

GALION a606 brake bleeders

My attempt to bleed the brakes on our GALION a 606 has been thwarted. I tried every wrench from 10mm(too small) to 12mm(too big) and every wrench from 3/8 to 7/16, including 11/32 with no joy.
Can someone enlighten me on this? Does it require a special application wrench? I searched a bit and figure on saving the frustration and ask the wise sages here. Thank you in advance

Where to buy quality cyl seal kits online?

I have acquired a neglected Case 580E backhoe and am going thru and fixing leaks. For front loader cylinder, i purchased two cylinder seal kits:

$19 from eBay, all no-name seals, fit and finish seemed lower than the below kit.

$32 from foxkit, included at least one SKF marked seals. Quality of fit seems more precise than the above.

My questions:
- does the use of name-brand seals make a difference ?

-where do you shop for quality seal kits?

Thanks !

Jd 410 wont go forward, reverse is perfect

Backhoe suddenly stopped going forward, pressure test indicates 0 when shuttle is in forward position

ZF Trans Oil in Hyundai HL740TM-3

Hey folks-

I bought a 2002 Hyundai HL740TM-3. The book calls for Dexron II, but the oil in the trans appears to be multi-weight engine oil, maybe like 5W40. One of my older mechs said that an outfit that he worked for used engine oil in their Terex trucks with the ZF trans. Any thoughts? Thanks.

MF 50 HXS

Hello All.
I bought a '92 MF 50 HX series S yesterday and ive a few little jobs to do on it. I was looking for the operator and service manuals if anyone can help?

Thanks

Cat th83 brakes

I replaced the brake disks and booster cylinder. With out the machine running the pedal goes all the way to the floor but I can get fluid at the bleeders on the axle. With the machine running the pedal will pump up but I have no brakes. With the machine running I can't gett fluid to the bleeders on the axles. I talked to cat tech service and was told to replace the booster cylinder so I did. I still have the same problem. I am getting 400 lbs of pilot pressure to booster. I called cat back...

Cat th83 brakes

CAT 966 regen status

hello

my cat 966 is having a problem with regeneration system and works for 1 minute then stopped
regen stutus is blocked

can someone help me in this please?

Hitachi 120-2 questions and anwsers

Hey everyone i bought a hitachi 120-2 last winter for 4,000 dollars which i thought was a smoking deal.
at first inspection the machine fired right up the idle up funtions worked. i moved the boom around and it seemed to bog the machine down. the guy i was with said it has got to be fuel filters."buy it" he said. so i did

one of the main reasons the people wanted to sell was because the machine had developed a new leak that was coming out of the middle of the undercarrage....

Hitachi 120-2 questions and anwsers

another 580c project. .

new guy here. Just got a 580c that has been sitting for years (upwards of 10). Started up immediately after I hotwired and jumped it. Got key now, so I won't need to do that anymore. I proceeded to blow the return line to the hydraulic filter. Replaced that with a hose that cost me $250. There's another return line that has a pinhole. I'm thinking about cutting it and hose clamping a hose onto it as a temp repair, but i am unable to find what the return pressure is supposed to be. Anyone...

another 580c project. .

New scraper -prototype

My grandson was running this yesterday. It had 5 hours on it when he got in it.
He parked it to take the photo.
Made by Mobile Track Solutions.
Sadly it is parked today. The engine has a bent rod along with two lifters and 2 stuck injectors. He said it just died.
View attachment 224461 View attachment 224459

428b Backhoe hyd dipstick

Hi guys, could someone help me out with the measurements of a hydraulic dipstick to suit a Cat428b backhoe? Mine is missing and I need to make one!! Thanks, Raymans' Daughter

John deere 310G park brake problems

I have had a hell of a time with my 310G s/n to310GX934593 park brake everything works fine on the machine except when the machine is driven for a short distance and park brake is applied then a buzzing sound is heard and is coming from solenoid area below the steering wheel column. I replaced all three solenoid pressure switchs witch are outlined in red but still have buzzing and the buzzing seems to be coming from that area
if I disconnect the X27 solenoid connector the buzzing stops but...

John deere 310G park brake problems

Hitachi EX120-2

Well, I had been looking at a EX200, and then a EX120 posted on Craig's list only 1.5 hrs from me. I took a look at the machine and it is pretty tight. Biggest complaint I have is that the bucket is pretty sloppy on the front pin. Seems it is kinda pricey to line bore a bucket to make it right and tight again.

The hour meter stopped at about 4800 hrs, but with the condition it does not appear to have more than 6-7K hours on it.

Issues we found:
Hour Meter not working
Coolant Temp gauge...

Hitachi EX120-2

EX200-2 Manual Pump Conversion Pro/con’s?

Hey guys. Another Ex200-2 here with to many issues with the hydraulics to mention. I bought the machine last year and put two new solenoids, and a new angle sensor in it. Had a deere tech set the pressures and make it right at the time. It ran great for about 10 months and then yesterday it started to stall on me. The pump is stuck at full stroke and won’t let the engine rev past L.

for some reason I can get it to rev up by activating my hydraulic thumb?? Every other function will...

EX200-2 Manual Pump Conversion Pro/con’s?

Do I have a cracked block?? John Deere 310A

I recently bought an old John Deere 310A that did not run (there is another thread on that). I got it running, but ended up with water in the oil and a "chirp" after a couple minutes. Suspecting a head gasket leak and seeing a plugged rocker arm as the cause I;
-Drained the oil last night (left the plug out to get as much water out as possible)
-Disconnected the intercooler lines and drained them in a bucket, also left open (which exit the pump below the water pump)
-Replaced the drain...

Do I have a cracked block?? John Deere 310A

Rigid vs rgn

We are in the process of moving up from a 160 to a 200-250 size excavator. We do a lot of residential, so access can be tricky. What setup is best, rigid or rgn trailer? Would like to haul multiple pieces of equipment at times . As well

3/4 ton welding truck remodel

I have been driving 2500 trucks with a welder in the back as a contractor for about 15 years now. I do residential and commercial doors, stairs, gates, railings, etc. i started with my equipment on a small trailer, but found it was a pain when I needed a big trailer too, to haul whatever I was installing. So they went on a skid in the truck. It works well, but severely limits room in the truck bed. Last year my compressor tank had developed fatigue cracks, so I bought a new tank($699) and...

3/4 ton welding truck remodel

Gasoline forklift losing power

I just got a komatsu 15 gasoline forklift. It starts up and has plenty of power. After it warms up it starts to die out. I van be full throttle and it gains and loses power. Is it bad rings? The line from the valve cover to the top of the carb. It blows out "air" when idling from the valve cover. I disconnected the tube to show you where I mean.

Just some work pics

Just thought I post up some pics of what I've been up to. Sorry about the sideways pics, I tried rotating them in windows, but it didn't stick.

View attachment 157749

View attachment 157750

View attachment 157751

View attachment 157752

White-GMC 94’ STC 330 N14

Yep I went and got the truck, just never made it home with it “yet” asking was $6500 got it for $5250, 313k miles and I will update more specs later with pictures. Anywho about that “yet” part I’m sitting here in it about 300 miles from home off exit 200 in North Dakota after it decided after 175 miles to lose power. Started down to 55 mph and after all is said it crawled in at 5 mph, so I guess I get iron problems out on the road at midnight. Opened up water drain valve it spit some out...

White-GMC 94’ STC 330 N14

Lumber Prices

Hello, I mentioned in my other post that I'm taking on a home build. We're doing this without a general, direct with the subs.... I got sideswiped by this lumber market.

Anyone have any theories or predictions they care to share about the immediate future of the lumber market?

We're ready to buy our lumber package anytime between now and the next few months and the prices have gone through the roof!!!

Case 580 Super N (diagnostic)

Can anyone tell me what these codes are ?

3368
3834
3411


Would appreciate it!!!

Cat 246b Charge pump test

Could someone tell me the method of testing the pressures on the hydrostatic drive charge pump? The machine serial is around PAT02400
I’m not 100 percent which port it is. And I don’t know what pressure I’m looking for. Also need to know if it’s just tested at idle, or even jacked up and in forward etc.

thanks in advance

J.D. 35D / Constant Flow Switch Kit

2012 John Deere 35D mini ex, serial #1FF035DXJCG268570. Need to provide constant hydraulic flow to small brush mower attachment. Dealer says they can install electric over hydraulic switch to accomplish same at the valve body, would rather not go the dealer route if possible. Was hoping you guys could provide some aftermarket switch kit options that I could install myself. Having zero luck finding anything like that online. thanks.

Concrete sealer?

Gutting the basement and need to seal the concrete walls, what's the best thing to use?

Bobcat diagnostic tool (rst)7003031

Hello sirs,can anyone know where to find the bobcat diagnostic tool 7003031?exept ebay?thank you.

Lists of projects

First up
Decide will try to establish gas to BILs chevy so load up to drop the GMc at the barn and attempt to motor the chevy to the shop.
Not today

Seems RF brake dragging severely
Have new caliper hoses so figured start there. Again Not today.
Local parts house will have calipers and pads in by morning, will assemble the new hoses to these then swap and install new pads.
RF both pistons freezing up extended, LF one piston has never moved out the other wants to hang and pads are all...

Lists of projects

New to me EX120-2

Just picked up an Ex120-2 and excited to get to work on it, so it can work on our new homestead

It has leaks and a few quirks, but I have to say, spending time on here reading over the posts gave me the confidence to make the purchase.
One item though popped up that the owner didn’t mention.

The Boom up is painfully slow. You pull back on the stick, and you can hear a valve or something staving for oil. If you push down on the boom and slightly pick the machine up, then the boom up...

New to me EX120-2

Caterpillar serial number/ year model

I cannot find a serial number guide for Caterpillar.
Any suggestions?
I want to know what the year model is of a D6D serial # 4X2592.

Cat 215 weak hdyraulics

i have a cat 215 that has been giving me some trouble. I am not sure if I have an engine power issue or a hydraulic issue. The problem I am having is the hydraulics are pretty weak. I had a couple of fuel problems that have been straightened out, rebuilt fuel transfer pump and new fuel lines and pick up tube in tank. Engine starts and runs well, no more missing and primer pump works as it should. Fuel pressure at injection pump is around 30-40 psi. When trying to dig with bucket or swinging...

Cat 215 weak hdyraulics

Cat ET with loptop

how much CaT ET with laptop ?
somebody helpme thnx.

TEREX TA64 Knuckle Boom Lift

I've been scouring the internet looking for a service/shop manual for this 1996 lift. All I can find is the parts and owner's manuals. Seems to be very limited results for this model.

Does anyone know if this lift has a direct parallel to another brand/name like SIMON or GENIE that I could look into instead? I'm mainly interested in the wiring schematics, but if I could get my hands on a full manual that would be nice too.

Schematic

Pls can someone help me with Dozer D6R AND D6H Schematic

pc78mr-6 electrical issues

hello , I have a PC-78 MR-6 that has some sort of electrical issues. The first problems that we noticed were with the solenoid that controls the swing parking brake. prior to this point all of the functions worked low and high speed the fuel gauge and temperature worked to include warning buzzer. we replaced the solenoid and while waiting for that new solenoid we cleaned and lubricated the old one to see if we could get by. you could start the machine shake the boom a little bit and then...

pc78mr-6 electrical issues

metal particles in gear oil from final drives in takeuchi tl140

i changed the oil in my final drives on a 06 takeuchi tl140 with 700 hours. this was the second time i changed oil. old oil came out frothy...with air bubbles. and the old oil had lot of metal "glitter" in it. i installed new oil and ran for a bit and drained it out, and replaced with new oil. ran another few hours and replaced oil again. still see "glitter" in the drained oil.
should i be concerned? running 75w-90 oil. would thicker oil provide more protection?

L10 cummins

I was told it didn’t want to start after moving it to the field . I got there and it started I changed fuel filter and cleaned bad air filter. They used it 2 days next day no start. I checked fire at Fuel shut off it was close buy a grain dryer So I couldn’t hear but after making good contact test light was flashing then I heated shut off clicking. I messed with it some more And it started then I tested key switch it was the factory one 2 million miles it didn’t seem good so I replaced it...

L10 cummins

GALION a606 brake bleeders

My attempt to bleed the brakes on our GALION a 606 has been thwarted. I tried every wrench from 10mm(too small) to 12mm(too big) and every wrench from 3/8 to 7/16, including 11/32 with no joy.
Can someone enlighten me on this? Does it require a special application wrench? I searched a bit and figure on saving the frustration and ask the wise sages here. Thank you in advance

Cat 955 L

Hello to everyone, i am a new member to this forum, but i have found much help in the past in various posts.

I Just purchased a 955 L. I dont know the date of the machine, there is a small plate welded on the engine side of the "dashboard" that reads 8Y8710. Is that the serial number?

The loader has been sitting for two years due to cylinder head failure, combustion was leaking in the cooland circuit. The previous owner took the head out but never got it fixed.
I Had a look at the...

Cat 955 L

Kobelco SK235SRLC

The machine does not throtle up as soon as you start to move the joystick for a function. If you wait a few seconds it will throtle up and work fine. if you try to lift or dig it will stahl. Preasures are in specs for the two main pumps . The Pilot pump is a little low about 650 psi, would that cause this? The govener motor was changed could that be it. Anybody have seen anything like this? Thank You, Mike 138.

International TD20 DVT573 V8 "flutters as turbo comes on"

History: This dozer was working fine when parked, then, sadly NOT USED for 5 years.


Got it running: Did all the new filters, oil etc... started and ran GREAT! But........

When you start to push or put a LOAD on the engine, as the turbo would normally build pressure (I presume) to increase power, it begins to produce a VERY AUDIBLE FLUTTER SOUND out the exhaust and power NEVER comes on.
Back off load and runs GREAT!
No other noises or irregularities.
With NO LOAD it will reach full RPM...

International TD20 DVT573 V8 "flutters as turbo comes on"

1988 john deere 510c project

Hi, I recently took a chance on purchasing a jd510c that needed a main hydraulic pump. After checking around and getting quotes on buying a refurbished one I decided to try my hand at rebuilding the old one. I should add too that the backhoe sat around for at least two years and needed lots of tlc. I was successful in the rebuild and we managed to get it moving . The hydraulics were slow at first and we discovered multiple leaks which we fixed and now they are much faster. During...

1988 john deere 510c project

580K Cummings Diesel Start problems

Hi everyone! We have a 1988 case 580k Cummings diesel with a starting problem. Replaced OEM starter about 5 years ago. 580 ran flawlessly for about 3 years then wouldn't start. Replaced starter again with OEM and ran flawlessly till now. Batteries measure fully charged, voltage drops look good, but it looks like bendix gear is extending but not fully engaging fly wheel and appears the gear is collapsing the spring on the bendix shift, possibility contacting the fly wheel? Any suggestions...

580K Cummings Diesel Start problems

7S blade serial # location

Hey my friends, need a little help to find blade serial # on a 7F straight blade. Tractor SN # 94N8650. I thought the # was on the right rear top. Tag is long gone. Tried wire wheeling the old paint layers off this morn where I THOUGHT it should be, and no luck. Am I looking in the wrong place?

Need Help Identifying Portable Water Pump (ITT Marlow)

Hello, I'm new to the forum and not sure if this is the right place to ask but I recently inherited a large portable water pump. I know nothing about this kind of equipment. I was curious if anyone had any information about it. Not sure when the pump was run last. I'm looking to get rid of it and was wondering how much something like this would be worth? Thank you.

help required to check Year of Manufacturing Komatsu Wheel Loader WA400-3

I want to check urgently the year of manufacturing of Komatsu Wheel Loader WA400-3 with Serial number 50148
anybody can help me asap. an early action in this regards shall be highly appreciated.
Best regards,

cat 955 H wont move and hydraulic dont work

looking for used parts , need torque converter,2 pumps, some gears , any help would be appreciated

jd 310b hydraulic problem

i lent my backhoe out to my brother. and now the front end loader and the hoe wont work. the steering seems fine, where should i start? it runs and drives fine. i have a parts manual but not a service manual.

Thermodyne question

Hi I was hoping those of you more seasoned people out there might know what I am looking at: I am looking at a running thermodyne it is a n/a, 2 valve,fuel pump with mechanical governor attached, the head has 20 bolts. which is all normal I am just wondering about the number stamped on the timing cover which reads:673E-5115727 . I thought all the n/a thermodynes would be stamped 673END ….. and the newer turboed ones would be 673ENDT.... so I just wondering why this one is just 673E.....? I...

Thermodyne question

Load tapping, no power

only thing I can think of is I blew a connecting rod. How can I test for this? I started it up this morning and immediately noticed the load tap coming from the motor. Here we go again!

Catapillar 262D Code 2204-3 & 3700-3 Questions

I am new the forum and I just picked up a 2014 Cat 262D. The machine runs fine but I noticed the other day that there was an alert light that was staying on but not flashing. Just like that check engine light So I went into the settings finding the event log. It had two codes displayed. The first code was 2204-3 Machine, Auxiliary Lever #1 Position Sensor voltage above normal. The second code was 3700-3 Machine, Loader Bucket Inclinometer Sensor Voltage above normal. I checked online...

Catapillar 262D Code 2204-3 & 3700-3 Questions

JCB 804

Planning to go check out a JCB 804, just looking for a landowner/farm machine so the specs seem good for me.

Owner states "Runs and operates need some Hydraulic adjustments for the drive motor to make it go forward mainly just when it turns might be a loose linkage? And adjustment on the grade blade won’t stay up, likes to fall down"

Anything in particular to check on the machine with regards to those 2 issues? Possibly a sign of serious problems?

The machine seems priced right so a...

JCB 804

Daewoo DH130 does not shut down

My cousin recently acquired a Daewoo/Doosan DH130 SN# 0263 89 04
The unit will not shut down when turning off the key. The book that came with it has some electrical diagrams which seem to not match whats in the unit. for example it shows an electric fuel pump, and electric fan but neither are on the unit.

Can anyone offer any insight on this?

John Deere 350B steering issue

A customer of mine just purchased a very clean JD350B six way dozer that looks like it hasn't had much use or much abuse, like is usually seen on the small dozers. It runs very well, the issue is the left side will not steer while going forward unless you absolutely pull with all you've got back on the left side lever, works fine in reverse, and the right side works fine in either direction. Pushes through a pile fine with no slippage at all. I belive this is a dry clutch machine with...

John Deere 350B steering issue

takeuchi TL126 second opinion

looking to get a second opinion on some issues with this unit. came in with hydraulics dead, engine starts and runs good - found no pilot pressure cleaned and inspected sub control valve and pilot solenoid and all looked good there so reassembled. at idle still no pilot pressure but at full throttle pressure rises enough for the loader pilot valve to function and loader will work as it should (gear pump) left track will try to move a little in either direction but with no power right track...

takeuchi TL126 second opinion

Case 1150E Low Trans Pressure & High Torque Converter Temps

My 1150E torque temps are running high into the yellow when it never has before.
Trans gauge never worked so I replaced it with an numbered psi gauge instead of stock color indicated gauge..
At first start up with everything completely cool, I'm seeing 175-190 psi trans pressure at full throttle & 50-60 psi at idle... Once warmed up pressure drops to 150 psi at full throttle & 20-50 psi at idle...
Not really sure where to begin.
Trans pulls within 3-4 seconds of start up as normally does...

Case 1150E Low Trans Pressure & High Torque Converter Temps

What are the differences in a Cat C/CR/e

Hi Cat fans, I'm looking at used cat 304 and 305's (particularly a 304e CR), but can't figure out what the .5, C or E or E2 or CR or combination of them mean. Could you enlighten me please?

Nissan 50 Enduro diesel forklift sloppy lift & tilt control

Hey guys. This Nissan 50 Enduro diesel forklift has a very hard to use lift / lower & tilt combination lever. It is SO sloppy that it has become difficult to control. (For example, to lift you have to hold the lever to the left & back towards the operator. To lower the forks, holding the lever to the right seems to do it most of the time. What in the world am I missing here??)

I don’t have much support with this issue & I don’t have a repair manual. Any help would be extremely helpful. I’m...

Nissan 50 Enduro diesel forklift sloppy lift & tilt control

Just some work pics

Just thought I post up some pics of what I've been up to. Sorry about the sideways pics, I tried rotating them in windows, but it didn't stick.

View attachment 157749

View attachment 157750

View attachment 157751

View attachment 157752

Cat 3126 rear main install tool

I'm going to have to put a new rear main seal in a cat 3126 sometime in the near future. When I get tired of it puking oil on the ground.

A guy local to me has this on Craigslist- is this the only tool I need, or do I need another adapter? Seller states that it does 3126- but I don't know.

I have a seal install tool for a 3208, I guess I should look and see what part # it is.

https://springfield.craigslist.org/tls/d/mansfield-cat-rear-main-installer-kit/7096502668.html...

Cat 3126 rear main install tool

Cat 312 final drive issue

1995 Cat 312 SN: 6BL00906

When I track forward or reverse the machine could push a mountain over. Plenty of speed etc... The problem is if I try to turn or try to move one track at a time, it basically falls on it's face. It doesn't stall the engine, it almost seems like fluid is bypassing.

Any thoughts on where I should start to look? Initially I thought maybe it could be the rotary manifold that needed to be resealed. A mechanic friend said if the seals where bad that it would also...

Cat 312 final drive issue

EX60-2 Thumb Circuit

I'm planning to add a thumb to my EX60-2 and need a hydraulic circuit to run it. I'm thinking of using the unused offset boom spool. It'll require me to fab up a pedal and run a cable to the spool since it's not hydraulic. This seems to be the most fool proof way but it will be pedal actuated which isn't the worst. I'm used to that from another machine I run. I'd add a relief valve so I could tailor it to the bucket hydraulics.

If I were to go electric over hydraulic and run it off buttons...

EX60-2 Thumb Circuit

Link Belt LS4300 CII no travel

Our year-long efforts to get our LS 4300 CII to travel are getting close to success as we've repaired and corrected so many issues on a machine that might have been otherwise condemned to junk. We've rewired and made a new control panel and run in bypass mode as the original computer was long gone. The rotary joint had been resealed prior. Unknown to the previous owner the main pump was going out and the pilot pump was being taken out due to bad bearings in the main pump. All of this has...

Link Belt LS4300 CII no travel

Hitachi EX swing issue

Hitachi EX120-2 Excavator
1995 4,500hrs.

I'm having issues with the swing motor. At first it would act lazy after 2-3 hrs. of use and now it barely swings after 10 mins from cold to warm. Meaning it moves left or right but at about a foot per 5 seconds with the bucket and arm curled in. Forget having a load in the bucket or boom extended out. I pulled the swing motor- full disassembly and reseal after no issue found.
At first thought I thought it was hydraulic oil getting hot and dumping...

Hitachi EX swing issue

Case 1845C advice.

Hello all. New to forum and first post. I just got a 1993 1845C that I traded my old 610 bobcat and some cash for, so I have about $6000.00 in it. Hour meter reads about 3300 and there is paint pen numbers above it 4400hr. So I assume the machine has close to 8000hr. The engine is dry and clean and runs perfect and is not near as grimy as the rest of the machine. Overall it looks pretty decent with about 40% tires. My biggest complaint is the left side has weak hyd drive pump and or motor....

Case 1845C advice.

Hi need help with case 1845c starts and cuts off

Hi need help with case 1845c starts and cuts off I have clean all connections .
some one put and electric fuel pump . so I install a off and on switch for the pump.
it was running good ,but lately when try to raise and lower the buck it it stops running and wont start so I let set for a day
and starts again, any one had the same problem any help will be appreciated.
than you Raul Austin Texas

Hitachi EX120

Machine has been sitting a year. Went to it today. And machine will run perfect at any RPM. Tracking works properly. But any boom function or swing function and the machine will choke down and almost cut off before it will preform that function. Any ideas?

Lists of projects

First up
Decide will try to establish gas to BILs chevy so load up to drop the GMc at the barn and attempt to motor the chevy to the shop.
Not today

Seems RF brake dragging severely
Have new caliper hoses so figured start there. Again Not today.
Local parts house will have calipers and pads in by morning, will assemble the new hoses to these then swap and install new pads.
RF both pistons freezing up extended, LF one piston has never moved out the other wants to hang and pads are all...

Lists of projects

416B Parking Brake Diagram And Adjustment

Does anyone have a clear pic or diagram of the parking brake caliper on a 416B ? The diagram listed in the factory service manual I have is of extremely poor quality. I have seen numerous threads referencing a 3/4” nut and jam nut in the Center of the caliper , but on the 416B it appears to be a different arrangement.
Without proper diagram the service manual seems like complete jibberish ! Any help would be greatly appreciated! Thank you in Advance !

Pre-emissions machine, or new? Brands to consider?

Hey guys (and maybe some gals on here), I'm in the market for a skid steer. I'm tired of renting, and have a bit of work to do around the house. 5 acres in the woods, so some dirt work, rocks, tree work, stumps, landscaping, gravel driveway, and a hobby of working on trucks, so moving junkers around and their heavy parts (axles, engines, beds, etc...).
There's a possibility of a few side-jobs through my mother's landscaping business, but I'm not factoring that into anything.

I've...

Pre-emissions machine, or new? Brands to consider?

Cab-Over

955L Torque Cooler Leak

Working on my 955L SN 85J4919. Still doing maintenance before I start operating it. It has been sitting all summer while I have been getting the tar substance out of the fuel tank. Cranked it and ran it for appx 20 at idle to find what appeared to be water/coolant leaking out of the front right of the machine if you are facing the grill. Looked in the grill and the liquid was coming from the aux cooler that is to the right of the radiator when facing the front of the machine. The next...

955L Torque Cooler Leak

Excavator parts are damaged

I have a personal mini excavator, and the undercarriage parts have been damaged recently. Is there any recommended way to buy it?

1986 Ford F700 dump hydraulic question

I've just bought a 1986 Ford F700 dump truck. There is a small hydraulic reservoir welded between the frame rails. There is a filler plug on top that is just a typical pipe plug. There is no vent anywhere in the system. The first time in a day that you lift the bed, it sounds like the pump cavitates. Sort of a rattling sound out of the pump. After the first lift, everything is fine. Subsequent lifts are smooth and quiet.

I notice that after the first lift, if I remove the filler plug,...

1986 Ford F700 dump hydraulic question

Svl95-2s def code9519 madmadmad!!

I’ve never been more disgusted with a machine than the kubota svl95-2s. Anyone know how to delete the dpf system. DONT CARE ABOUT THE LAWS AND NOT WANTING INFO ON THE ENVIRONMENT!!! I only want info on how to delete, destroy, bypass, rig or whatever I have to do to never put def in this POS again. Any help would be greatly appreciated!!! I’m not taking it back to kubota to get anything done! So if I have to buy computers, parts or whatever, that’s what I’ll do. I’m at my end with this...

Svl95-2s def code9519 madmadmad!!

Wanting to contact Scrub Puller

In the next 2 weeks or so I'm heading south from Far North Queensland and going past near where Scrub lives. Can someone here who has contact with him PM me details so we can catch over a culpa.
Thanks in advance.



Bloody so-called intelligent devices that can't spell----------should read, Wanting

another 580c project. .

new guy here. Just got a 580c that has been sitting for years (upwards of 10). Started up immediately after I hotwired and jumped it. Got key now, so I won't need to do that anymore. I proceeded to blow the return line to the hydraulic filter. Replaced that with a hose that cost me $250. There's another return line that has a pinhole. I'm thinking about cutting it and hose clamping a hose onto it as a temp repair, but i am unable to find what the return pressure is supposed to be. Anyone...

another 580c project. .

Some Fire Damage

The air cleared up Friday and yesterday so I did some drive by's of some of the damage that happened. East winds on the west side of Washington State have always been a problem. Most of the time the winds blow from the west of southwest and the trees kind of get used to that. They don't seem to put out much for roots to the east. Full summer and lots of growth creates lots of sail area and the big ones just fall over. Lot's of rumors about people setting fires but I've only heard the news...

Some Fire Damage

Mini Excavator Motor Oil

OK, So yesterday I took a trip to a Case dealership.We talked price ext. I was asking about maintenance. Motor oil, grease, filters bla bla bla.Well the salesman asked the man behind the counter.This is when the **** hit the fan.I asked about filters. he told me that Baldwin filters are what is recommended.I asked about Wix. BTW,I am a long time Wix user and will continue to be so.He showed his ignorance telling me that the Wix brand does not meet the requirements that Case requires.I asked...

Mini Excavator Motor Oil

Fabrication videos

Post any video about metal working, this is a good one.

Bobcat s185 bogs down when using hydrolics

I have a bobcat s185 turbo, and it has some bogging down issues. The bucket can move up and out with no problems, but as soon as i move the bucket down and in (at the same time), the bobcat bogs down and nearly stalls. It also bogs down with fast acceleration or top speed. It especially doest like it when combining these 3 functions (bucket down, in, and full movement). When doing all 3 at once, the belt will slip and sqeak.

I just replaced the hydrolic/hydrostatic fluid and filter (messy...

Bobcat s185 bogs down when using hydrolics

1968 case 680e won't go into fwd

My 1968 won't go into after it gets warm will go in reverse. Goes in fwd when cold. Tried changing fluid and cleaning screen had no luck i have fwd and reverse clutch plates for it but would like to know for sure before I drop the transmision out of it

New scraper -prototype

My grandson was running this yesterday. It had 5 hours on it when he got in it.
He parked it to take the photo.
Made by Mobile Track Solutions.
Sadly it is parked today. The engine has a bent rod along with two lifters and 2 stuck injectors. He said it just died.
View attachment 224461 View attachment 224459

1969 Case 580 CK 188 Power Shuttle diesel won't start

This tractor would start easily with weak battery whether cold or hot after redoing the heads. While moving to re-attached backhoe front wheel lugs popped and wheel came off crashing to concrete. Motor kept running fine but after turning it off it would not restart after replacing front end/hubs - unless we used ether.


Thought something to do with fuel so rebuilt fuel pump - no change: had it rebuilt again professionally - no change; replaced fuel filters and ensured all fuel lines open...

1969 Case 580 CK 188 Power Shuttle diesel won't start

SVL75-2 + Snowblower rookie

Hi all!

A few rookie questions about operating our SVL75-2 with a Kubota snowblower.

Firstly, I had the hydraulic lines disconnected (and had released the pressure before disconnecting by pushing in the connectors) and they leaked on the shop floor. Is there a standard practice to avoid this?
View attachment 224796



Secondly, the dealer has the lines tie wrapped together so I'm unable to use the hose routing guide on the load arm, and this puts the smallest line under a lot of...

SVL75-2 + Snowblower rookie

Logging Cartoons

View attachment 189794 View attachment 189795 View attachment 189796 View attachment 189797

Need a new battery. Single or double?

My NH 575E has always started draggy. It generally starts okay in the summer but has always had to be jumped off in the winter. Winters aren't that bad here. Even in summer it spins slow but usually starts. I have replaced the alternator and starter in the recent past and as far as I can tell neither those or the cables are my problem. When I first got it I replaced the cable ends with tinned brass solder on ends.

My tractor came with a single battery vs the dual setup. I think I have a 850...

Need a new battery. Single or double?

need Ford 555B backhoe steering rebuild kit

Hey!

I am having problems finding the correct part number (and where to find one) for a steering cylinder rebuild kit for a Ford 555B (tag says model DF8111)

It seems the problem is there are two sizes of cylinder rods ... .685 inch diameter and 20 mm (.787) diameter

I need the one for the the 20 mm (.787) diameter rods.

I am hoping to find a kit (see pictures of ones that have just the seals and ones that have everything including c-clips and wire retainer rings) that has "all" the...

need Ford 555B backhoe steering rebuild kit

New Holland 555E Transmission Oil Pressure Warning Lamp

Trying to figure out the diagnostic steps when this warning lamp and buzzer come on. The repair manual really doesn't acknowledge it from what I can find.

Cat 225 cylinder re-sealing

A project I want to tackle soon is the re-sealing of my CAT 225 bucket & boom cylinders. I have re-sealed many cylinders in the past for my other equipment, but nothing with more than ~1100 ft-lb required for the piston nut torque. These CAT 225 cylinders require around 2600-2900 ft-lbs to properly torque the piston nut. I do not have a cylinder repair bench of any kind. In the past I have borrowed 600 ft-lb torque wrenches and torque multipliers to get jobs done, but I have no source for...

Cat 225 cylinder re-sealing

PTO hydraulics on a GMC Top Kick

I've bought a fire truck as a replacement for my C65 I need hydraulics for the dump body now on the C65. It won't carry tandem weight. I'd estimate body, and load together at 17000.

My engine is a Cat 3208Turbo. Try as I might I can't find room for an engine mounted pump. Shaft drive off the front of the engine isn't going to work as the radiator is in the way, and includes coolers for transmission, and engine...

PTO hydraulics on a GMC Top Kick

95 GMC Topkick hesitating and miss firing...

Have a 95 GMC Topkick with the 6.0L TBI engine. Put a new distributor in last year and then new fuel pumps this year. Was running great but started to sputter so figured was getting low on gas (fuel gauge isn't accurate). Put some gas in and seemed OK for a bit but started sputtering again and getting worse. Started and idled great but no power when trying to drive. No check engine light came on. After finding a mouse nest on the engine (complete with live mice, ewe) and remnants in the air...

95 GMC Topkick hesitating and miss firing...

New to me 143 H

Hi everyone!
I just bought an ex-county machine off of BigIron Auctions.
CAT0143HV1AL01163
Pretty low hours, around 4500. Called to see if oils needed changed up, they said it had been in shop last winter. Oils changed, drive chains changed, trans solenoids replaced, and some maintenance done in the front wheels.
So a couple questions.
Should the front wheel assist be used at all times? Is there a choice?
Any quirks I should know about on that machine?



New to me 143 H

TD-15 not moving forward or backward

View attachment 224754 View attachment 224754 Hello all, so we have an old TD-15 Dresser that we know virtually nothing about. Was running good until it stopped moving back and forth, has been sitting where it is since about january now. Still turns on at the first press of the button. Almost nobody in my area knows about this machine, been looking all over for anything that can help me ID the thing but so far have found nothing. Was told that the issue sounds like it could be...

TD-15 not moving forward or backward

CAT 966C - My first ride in heavy machinery

Lawrence, a new member [71 year old ex Navy Electrical Engineer] now involved in research and development in small scale hydro energy technology solutions.

I picked up a 966C Loader yesterday and floated it to a small plot of land (10 hectares) in Western Queensland alongside the Condamine River. I need it to do some earthworks over the next 6 months and construct a small reservoir (about 5 ML capacity) at 10 M head, for an experimental pumped hydro system design (hardware + software) that...

CAT 966C - My first ride in heavy machinery

855E Case does not run need to release Parking brake.

We are needing to pick up a Case 855E track loader and bring to the shop, the unit does not run. How can we release the parking brake manually so it will roll to let us get it loaded? Thank you.

Old conventionals at work

Heres a few pictures a couple of mine and some of contractors i operate for. Any one else have any old timers at work today?

Looking for a hydraulic thumb

What’s the best aftermarket hydraulic thumb manufacturer? Going on a 250 size machine

Genie Controls Issue Puzzling

Having a puzzling issue with a Genie 2632 electric scissor lift with Genie's Smart Link diagnostics box

For some reason, Ground controls (GCON) works when key is turned to the right
But when key is turned to the left for PCON nothing happens, no LCD, nothing.
So we can have the lift go up and down from the ground (but no driving because there is no joystick on the GCON and the PCON does not want to turn on when we try to turn key to left PCON mode)

The odd thing is in right/GCON mode, the...

Genie Controls Issue Puzzling

Need Help Identifying Portable Water Pump (ITT Marlow)

Hello, I'm new to the forum and not sure if this is the right place to ask but I recently inherited a large portable water pump. I know nothing about this kind of equipment. I was curious if anyone had any information about it. Not sure when the pump was run last. I'm looking to get rid of it and was wondering how much something like this would be worth? Thank you.

PTO hydraulics on a GMC Top Kick

I've bought a fire truck as a replacement for my C65 I need hydraulics for the dump body now on the C65. It won't carry tandem weight. I'd estimate body, and load together at 17000.

My engine is a Cat 3208Turbo. Try as I might I can't find room for an engine mounted pump. Shaft drive off the front of the engine isn't going to work as the radiator is in the way, and includes coolers for transmission, and engine...

PTO hydraulics on a GMC Top Kick

Ed's 77 Terex 72-41

Starts and runs, but has a few issues before it's ready for work. The emergency brake valve next to the seat was leaking and wouldn't build pressure, I got a rebuilt one locally. The valve in front of it had a broken lever, also got a new one. I'm thinking it's a 4WD switch, not sure. I have a parts manual coming today, no service manual yet.

Also the transmission is leaking, there's a pretty good drip coming off the small round thing with hose towards center of the picture (underside...

Ed's 77 Terex 72-41

941 Bucket Positioner Repairs

View attachment 161303 View attachment 161304

Since purchasing this old machine a year ago, the bucket positioner has not worked & is on my bucket list of things to repair. The rod/clamp is missing that clamps onto the cylinder rod. The valve bracket has some damage to it, as does the guard. I would like to try to get the positioner working again if I can without spending too much on it.

I see there are three lines leading out of the valve but know nothing about how it works....

941 Bucket Positioner Repairs

Massey 30H TLB

Hello all, New to the forum. Just got a new to me MF 30H with side shift hoe. It has the usual rusted out cab and such but works great. Planning on fixing it up and searching for some parts. This model seems a bit rare but has some parts in common with others models. I'm looking to see if anyone has a 30E,40E 50E with that red safety lock bar on it part#1473085m91 for holding up the loader. I'd like to get some pics and measurements from one, so I can fabricate one. No print available from...

Massey 30H TLB

Genie GTH 1048 Telehandler shutting down

Hi Yall,
I am a new member but have a machine that is giving me some trouble. I have a 2006 Genie 1048 telehandler that is shutting down. I just bought this machine a little over a month ago from a private dealer who sells stuff on the side. Engine is a John Deere 4045. I will start it up first thing in the morning, and it will run for about 8-10 minutes fine, then will shut off like you turned the key off. After that it will only run a minute each time before shutting down. If you leave the...

Genie GTH 1048 Telehandler shutting down

BELAZ 450 ton dump truck specifications released along with a model of the truck!!!

You can go to http://www.belaztrucks.com/belaz-announces-450mt-truck/ and download the PDF and see the specifications of the truck.

I thought the machine is going to be big but not that big... It is 20 meters long, 8.20 meters high and almost 10 meters wide. What struck me most was its empty weight -360 tons. ( 110 tons more than the previous model). What makes it unique is the 4x4 and 8 wheels it has. You can definitely pull anything with a 360 ton 4x4 truck... Even the...

BELAZ 450 ton dump truck specifications released along with a model of the truck!!!

On the Road Again

Changing main bearings on JD 410

I am doing an in-frame on my 78 john deere 410. Does the oil pump have to be removed to access the front main bearing? I'm new to rebuilding an engine.

Thanks,
Blake

sevice manuals

looking for technical,workshop manual for cat 320 B

2005 cat 305 engine UPDATE!!!!!!

Engine rebuild update. I had a starting problem. Had to get injectors and high pressure pump rebuilt. I got the motor running tonite but I only have idle. When I turn the dial throttle stays the same rpms will not increase. I can watch the electronic actuator move the throttle arm. Also when I lower the saftey arm on left side of seat I have no operation of any hydraulics. Keep in mind I bought this machine not running so I may be missing something. Any thoughts greatly appreciated. Thanks

komatsu D41E-s 1991 dozer

Hi any one with any info on a komatsu D41E-3 1991 dozer good or bad.What are they like going to look at one with 9000 hours on it,PAT blade and rippers.
Looking to buy another dozer looked at a few already just leaving my options open at the moment.

What brands of elevating scrapers used a Hancock design bowl?

I've been told the Terex S17E. That bowl sure looks similar to the Wabco. Maybe I'm wrong. But the stationary cutting edge, and the strike-off blade attached to the moving floor have similar designs. The large pipe across the top rear of the bowl, etc. Later designs have the laid up box fabrication of the bowl walls like the backside of the Cat six way blades.
Tying the lower front of the bowl walls together with a cutting edge would sure strengthen the walls at the lower front

Looking for scraper drawbar

I’m looking for eject scraper drawbar for a John Deere 9430T anyone happen to have one laying around or know of anyone? Thanks

Memories for us old truckers

Oxbow started this thread at the HTF forum.

Truck Shop

Grizzly Trucks

Ok....its a bit of a stretch but I am pretty sure the original guys had logging in mind when these trucks were built.I have been Grizzly hunting for a few years and have found almost half of the trucks built are all on Vancouver Is.There are three of them just in Qualicum...I have found around 3/4 of them
I lived and worked in North Van when these trucks were built..I had just finished my 10 years at Pacific ..

This is truck #1 of 13 or 14 trucks..It has been on the Island for years and...

Grizzly Trucks

PTO hydraulics on a GMC Top Kick

I've bought a fire truck as a replacement for my C65 I need hydraulics for the dump body now on the C65. It won't carry tandem weight. I'd estimate body, and load together at 17000.

My engine is a Cat 3208Turbo. Try as I might I can't find room for an engine mounted pump. Shaft drive off the front of the engine isn't going to work as the radiator is in the way, and includes coolers for transmission, and engine...

PTO hydraulics on a GMC Top Kick

JCB 509-45

Hey guys, I got a issue and I'm not sure anyone can help me but here is what I got.


JCB 509-45

10-7 CAN fault - RAS switches to mode 1 - locked Check related CAN bus wires and connectors
buzzer is on and red caution light on the right instrument panel is illuminated

I checked resistance on the green and yellow CAN link from RAS to the right dash panel and they are good.
Can anyone here help?

thanks

Links or resources to find equipment condition inspectors?

Not sure what you might call them, but looking at a couple pieces of equipment that are not local and I cannot rely on the seller to give an accurate representation. I could get in a rental car but it would sure be easier to just get an experienced eye on it and relay some info. I know these guys are out there and several auction houses have these reps.

However, I do have a little concern (maybe not warranted) about snaky people trying to sham a potential purchase. I could see the...

Links or resources to find equipment condition inspectors?

John Deere 310G Runs Erratic Code F494

I have 2004 JD 310G that I recently purchased with 1300 hrs. It cranks easily and idles at 900 rpm. It had set up a few years due to previous owner health. It has a slight miss but barely noticeable. If you leave at idle after 3 minutes it starts running badly. Shut engine off and immediately start again and runs good for 3 minutes and does it again. Very consistent hot or cold. If running at higher rpm also runs fine for about a minute. Then if I shut off and recrank runs fine for a minute...

John Deere 310G Runs Erratic Code F494

Cat 312 final drive issue

1995 Cat 312 SN: 6BL00906

When I track forward or reverse the machine could push a mountain over. Plenty of speed etc... The problem is if I try to turn or try to move one track at a time, it basically falls on it's face. It doesn't stall the engine, it almost seems like fluid is bypassing.

Any thoughts on where I should start to look? Initially I thought maybe it could be the rotary manifold that needed to be resealed. A mechanic friend said if the seals where bad that it would also...

Cat 312 final drive issue

New scraper -prototype

My grandson was running this yesterday. It had 5 hours on it when he got in it.
He parked it to take the photo.
Made by Mobile Track Solutions.
Sadly it is parked today. The engine has a bent rod along with two lifters and 2 stuck injectors. He said it just died.
View attachment 224461 View attachment 224459

Komatsu

Any good leads on komatsu manual downloads? Getting ready to rebuild one on a D155AX-6

Need a new battery. Single or double?

My NH 575E has always started draggy. It generally starts okay in the summer but has always had to be jumped off in the winter. Winters aren't that bad here. Even in summer it spins slow but usually starts. I have replaced the alternator and starter in the recent past and as far as I can tell neither those or the cables are my problem. When I first got it I replaced the cable ends with tinned brass solder on ends.

My tractor came with a single battery vs the dual setup. I think I have a 850...

Need a new battery. Single or double?

980H Transmissions issues

Hey guys I'm working on my 980h JMS03132
so far I haver had hydraulic, steering, and braking issues since I bought it last winter.

Now I'm on to the transmission issues haha. the machine ran great all day saturday no problem all day. monday warm it up and grease it and go to dig into some piles and first gear has no power.
after a little playing around and getting it warm i learned that 2,3,4 all work properly with full power in both auto shift and manual. when you drop it into first to...

980H Transmissions issues

FYI this is a fun Cat 930 post

Hello All

Caterpillar 930 wheel loader serial numb 41K00289

This machine was destined for the scrap yard 7 years ago.

It had a broken front spindle that Caterpillar could not even give me a part number or price for.

So I got to cursing around the internet and found one in a dismantling yard.

I put it together and they completed the present use of the machine.

It then sat for about a year. When I ask about it they said they were thinking about scraping it.

I looked it over and decided...

FYI this is a fun Cat 930 post

Cat 135h motor grader bluish white smoke

got a cat grader 135h serial 3yk00148 with 3116 engine #98z17710 and its got a hard start and quite a bit of bluish white smoke.
could it be the injectors?
any one can help with the injector timing dimension? the specs from the valve cover plate are not visible.

John Deere 270 Series 2

Good morning all,
Picked up a new to me JD 270, I would appreciate any info I can get on this machine. First problem is the foot controls, what is the proper way to activate? the lever near your right leg doesn't seem to be connected to anything. There is no switches on the "dash", other than a light switch so I have no idea how to go from hand controls to foot. Second is the auxiliary hyd, should there be a switch for that or is that something I need to add? I have been going through the...

John Deere 270 Series 2

Volvo Earthmoving machine faulty codes

I am asking for a volvo machine faulty codes just to familiarise with the volvo systems

CAT 988 H inching pedal adjustment

Please help,we have a CAT 988H loader. The operator is complaining about the inching pedal. His left foot angle is getting sore because the inching pedal is not working right. How do I adjust this pedal please. Can I adjust it manually or I have to use ET to adjust the pressures, please help.

624K fork auto tilt

Good afternoon everybody, I have a TRAM 624K with fork attachments, which in idle will automatically tilt up as far as possible. I’m pretty new to HE maintenance so I’m looking for advice. The upper fork hydraulic cylinders will just compress after a couple seconds of idling in whatever position it’s in.

Fusion Coupler

Any one knows if the 950K/M/H Fusion coupler can fit on CAT 950G loader?

Thanks.

941 Bucket Positioner Repairs

View attachment 161303 View attachment 161304

Since purchasing this old machine a year ago, the bucket positioner has not worked & is on my bucket list of things to repair. The rod/clamp is missing that clamps onto the cylinder rod. The valve bracket has some damage to it, as does the guard. I would like to try to get the positioner working again if I can without spending too much on it.

I see there are three lines leading out of the valve but know nothing about how it works....

941 Bucket Positioner Repairs

Wheel loader sizes

What Michigan or Clark wheel loader be comparable in size and weight to a Cat 955 track loader?

Hitch Doc Dual Dozer

I am wondering if anyone has used these and their thoughts. I'm looking to get a 7 or 8' one. Also anyone know where to get a good used one? Any thoughts appreciated.

CAT New Gen Dozers Prefix Serial numbers

CAT will move to New generation of dozers D1 to D11, does any one know the prefix serial number of those dozers?

I know D5 has a Z6A and D6 has SA9 and RA9.

Thanks.
View attachment 224468

Rigid vs rgn

We are in the process of moving up from a 160 to a 200-250 size excavator. We do a lot of residential, so access can be tricky. What setup is best, rigid or rgn trailer? Would like to haul multiple pieces of equipment at times . As well

Making Profits Mini Excavator.

OK Well I guess the title spills the beans!A while back I had the notion to do some work with a mini excavator.Well, it seems like everyone rained on my charcoal. Anyway the idea about doing something like that notion is still alive in my hippocampus.. I stumbled across this video. He leaves a lot of questions, like insurance,business license and the like.Myself I will be the only one working. Sort of a one man band.However he makes several valid points. There is monies to be made, and you...

Making Profits Mini Excavator.

85 Ford F-800

I just got the above mentioned truck and have been waking it up from approximately 5 to 7 year slumber. After removing the entire heater box and heater core to remove the stinking rats nest and washing the entire vent system with pine-sol, I have moved on to the engine.

While I was changing the oil, I noticed the fuel pump (370 gasser) looked like it has a filter attached to it. Does anyone have any experience with these? Is there a filter at the fuel pump? Also, there is a fuel...

85 Ford F-800

Just some work pics

Just thought I post up some pics of what I've been up to. Sorry about the sideways pics, I tried rotating them in windows, but it didn't stick.

View attachment 157749

View attachment 157750

View attachment 157751

View attachment 157752

HELP NEEDED: caterpillar m313D wheeled excavator travel power very low

Hi,

I am looking for some or any help with my 2009 caterpillar m313D wheeled excavator, serial number catm313djw3h00836.
the machine has very little to no power to the travel wheels in either hi or low speed but is digging fine or maybe a little slow on the stick speed.

So far, I have replaced the travel motor, the clutch packs in the transmission, replaced the upper swivel seals, and swapped out almost every solenoid from a similar machine.

I have cat et and it is showing no...

HELP NEEDED: caterpillar m313D wheeled excavator travel power very low

Check Valve Issue? (JCB 1550-B)

I've had this machine for probably 20 years. When I first got it, I changed out filters. I seem to recall when I changed the hydraulic filter, there were small bits of metal in it (on the magnet). Since then, when I change it out, I've always feared more metal bits but instead, I have what I'd call small iron "filings" like dust.....which strikes me as probably more typical.

(that was just backstory)

One thing it's always done and is getting worse.... the backhoe will slowly drift to...

Check Valve Issue? (JCB 1550-B)

503 Galion hydraulic fluid filter

Brought this one back from the dead need some help anyone know where i can fined the correct filter for the hydraulic tank also the best manual for it, plus fluids , what type of grease should i use I is a nice unit and would rather do preventive maintenance then have it brake when i need it
serial no 503-HDC-05690 if you have any info on it let me know
I also did did a motor transplant in it it had a d-236 or d- 282 soif you need parts for your let me know

On the Road Again

Dust Control Equipment

Hello, I'm a first time owner/builder for a custom home on 1 acre in the Las Vegas area. I have taken a dust class to get our dust permit. Can anyone make a suggestion on a good hose / spray setup I can buy to manage dust on our site during the entire period of construction?
We have a fire hydrant on one corner of the lot and our future water main already stubbed in at another corner of the lot. The city has said we can get a plumber to rig a hose bib off our future water main supply...

Dust Control Equipment

Ford 555 coolant in oil

Ford 555 has a 3 cylinder diesel with a turbo that looks aftermarket.
Ive had it 6 months and it has been working great until yeasterday It wouldn’t turn over. The engine was hydro locked with fluid in the cylinders (mostly the rear one) when i removed the injectors it woud turn over and sprayed fluid out of the injector holes.

My first thought was i had water in the tank that was being injected into the cylinders but the volume of fluid In the cylinders seemed too great

My rad has had a...

Ford 555 coolant in oil

Insurance

Let talk insurance.
Still in the planning process of purchasing a 40t class truck crane and starting a taxi crane service in the midwest.
I know insurance is a heavy expense in this business, can anyone give me a general idea of what I might be looking at for a single owner operator setup per year? And insurance providers I might call to get quotes.
Thanks!

69 580CK Instrument Panel Removal

I figured I would remove the instrument panel from my 580ck today and try to figure out why the fuel gauge isn't working and the tach well it does what it fells like. I removed all the bolts and screws. I had to remove the fuel shut off cable from the fuel pump the whole cable had to come out of the dash. I went to move the dash back, up, and out and nothing. I get maybe about 1/2 and inch.

I believe it is being held in place by the clutch pressure gauge. I stuck my hand up under...

69 580CK Instrument Panel Removal

Just got a 941B have some questions.

Hello,
Just picked up a 941b Cat. Machine has seen some use. Undercarriage is worn but usable. Where would I find a manual on it so I can see what services need to be done, fluids etc . Also the bucket tilt control is backwards. I thought maybe someone put something together wrong but the plate shows its
Correct. Having a hard time adapting. Anyway I can switch it ?

Case 85XT Starts but Quits Immediately

Hi SS Gang -

Rookie member here, so please bear with me.
I have a 1998 85XT with an intermittent starting issue. It starts (like as soon as you touch the key) but immediately shuts down when I release the key. I would never make a habit of this, but if I hold the key in the start position for a second longer, it keeps running.
i assume it has a fuel solenoid (although I can't see it ... probably hiding behind the inj pump). I also assume that these things have a relay (maybe dedicated)...

Case 85XT Starts but Quits Immediately

cat 941B loader governor problem

throttle control will not pull back beyond half way point.
linkage is working properly and has full, smooth range when disconnected from governor
opened governor compartment and slotted pin moves freely when pushed down by oil pressure from the top oil line but seems to not engage with rotating portion when trying to move throttle into wide open position properly
oil and filter changed so it should not have anything to do with the travel of internal workings

when problem first started, oil...

cat 941B loader governor problem

980H Transmissions issues

Hey guys I'm working on my 980h JMS03132
so far I haver had hydraulic, steering, and braking issues since I bought it last winter.

Now I'm on to the transmission issues haha. the machine ran great all day saturday no problem all day. monday warm it up and grease it and go to dig into some piles and first gear has no power.
after a little playing around and getting it warm i learned that 2,3,4 all work properly with full power in both auto shift and manual. when you drop it into first to...

980H Transmissions issues

John Deere 590D idler noise

My 590d that I purchased this spring had a new idler installed. That track side has been noisy since I bought it. Yesterday I noticed that the inside face of the idler is all shine from wear. I new to track machines.
Does the idler have a bearing?
Is it one unit?
Is there adjustment or shims?

thank you for any help

All the goody

This came in yesterday not sure how.

Galion 80, 90, 100, 110 and 125 Cranes SERVICE MANUAL

Hi All: We own a Galion 90A and have the Service Manual that covers the Galion Crane from Model 80 to 125. We also have the Engine Manual for the Detroit Series 53 Diesel Engine. If anyone wants a digital copy e-mail me back with your e-mail to see what we can do.
Cheers :canada Ayrhead
Here is a picture of our unit when we bought it 3 years ago.

Hitachi Workshop Manual

Has anyone got a workshop manual for a Hitachi EX120-5 for sale?

15" split rim Dayton style wheels wanted

I am looking for some rims for an old lowboy. I need a 15" split rim for a spare and I also would like to find some 17.5 Dayton style so I can start converting to tubeless.

opinions wheel loaders case / case poclain

hello, if it were possible we would like to know opinions on performance old wheel loaders from the 90s case / case poclai, strengths defects performance performance,

Model Number: Case 621 B (90's of construction)? what do you think?
blades with capacities from 2 to 3 cubic meters. thank you...

opinions wheel loaders case / case poclain

Adding Ramps to a PJ Trailer?

I have a 2012 5 Ton 24' Flatbed Trailer by PJ. I really love the trailer, however the ramps on this unit seemed to be an afterthought. I know they make ones with nice ramps, but this one just doesn't have them. I bought it used from someone who drove it once and could not get it into his shop, so he sold it. The Ramps were so comically steep, the previous owner expanded each steel ramp by 4 feet making the ramps around 150-200 pounds each and they no longer fit into the onboard storage....

Adding Ramps to a PJ Trailer?